{"id":498,"date":"2026-03-27T05:13:14","date_gmt":"2026-03-27T05:13:14","guid":{"rendered":"https:\/\/isbm-technology.com\/?p=498"},"modified":"2026-03-27T05:14:56","modified_gmt":"2026-03-27T05:14:56","slug":"large-format-hand-soap-refill-bottles-isbm-production-guide","status":"publish","type":"post","link":"https:\/\/isbm-technology.com\/it\/application\/large-format-hand-soap-refill-bottles-isbm-production-guide\/","title":{"rendered":"Large-Format Hand Soap Refill Bottles: ISBM Production Guide"},"content":{"rendered":"
\n

<\/p>\n

\n
<\/div>\n
<\/div>\n
Application Insight \u00b7 Hand Care Packaging<\/div>\n

<\/h1>\n

As refill and bulk-buy formats reshape the hand soap category, 1L\u20135L bottles are becoming a production priority. This guide covers how stretch blow molding technology handles large-format hand soap container manufacturing \u2014 from handle integration to high-output ISBM machine selection.<\/p>\n

Tecnologia ISBM<\/span>
\nRefill Bottle Manufacturing<\/span>
\nLarge-Format PET Containers<\/span><\/div>\n<\/div>\n

<\/p>\n

\"Large-format<\/div>\n

<\/p>\n

Large-format hand soap containers \u2014 spanning the 1L countertop refill, 2L institutional bulk and 5L commercial dispenser formats \u2014 are among the fastest-growing packaging segments in the Australian personal care market. Consumer adoption of refill models, combined with cost-efficiency pressures in aged care, hospitality and food service channels, is driving sustained volume growth in bottle formats above 750ml that retail shelf space previously excluded. Plastic bottle manufacturing for these larger formats presents a distinct set of engineering challenges: bottles must be ergonomically manageable when filled, structurally adequate for stack distribution, compatible with both pump and pour dispensing systems, and produced efficiently at the output rates that large retail and institutional supply chain volumes demand. One-step injection stretch blow molding is increasingly the platform of choice for meeting these requirements simultaneously.<\/p>\n

<\/p>\n

The Commercial Case for Large-Format Hand Soap Packaging<\/h2>\n

The refill model for household hand soap has reached mainstream market penetration in Australia, with major supermarket chains and direct-to-consumer brands offering 1L\u20132L refill packs across both the grocery and home delivery channels. The sustainability narrative supporting this format is compelling: a single 1L refill pack replacing four 250ml single-use dispensers reduces PET consumption by 35\u201350% per litre of product, cuts secondary packaging volume by equivalent margins, and reduces transport emissions by consolidating product density. These metrics resonate with Australian consumers increasingly familiar with the packaging hierarchy logic of reduce-reuse-recycle, and with corporate buyers in healthcare and hospitality managing sustainability KPIs under national voluntary commitments.<\/p>\n

For bottle manufacturers and brand owners, the commercial dynamics of large-format hand soap production differ from standard retail 250\u2013500ml runs in several important ways. Total bottle count per production run is lower, but material weight per bottle is substantially higher \u2014 a 2L hand soap container may use 35\u201355g of PET compared to 8\u201315g for a 250ml retail bottle. This shifts the economics of machine selection toward high-clamp-force and large-shot-weight ISBM platforms rather than the compact, high-cavitation machines optimised for small-format PET bottle manufacturing. Understanding these differences guides both machine investment and production planning decisions for large-format hand soap programmes.<\/p>\n

<\/p>\n

ISBM Process Advantages for High-Volume Refill Bottle Manufacturing<\/h2>\n

One-Step Process Efficiency at Larger Preform Volumes<\/h3>\n

At larger bottle volumes, the one-step macchina per stampaggio a iniezione-stiro-soffiaggio<\/a> architecture retains its fundamental advantage of thermal continuity from injection to blow \u2014 and this advantage becomes more significant, not less, as preform weight increases. In two-step processing, a 40g preform for a 2L bottle requires substantially more reheat energy and time than a 10g preform for a 500ml bottle, introducing greater thermal non-uniformity in the reheated preform body that manifests as wall thickness irregularity in the blown container. The one-step process eliminates this reheat step entirely, providing consistent biaxial orientation in the 2L bottle body with the same process repeatability that characterises 500ml production \u2014 a significant quality advantage for the thick-walled, high-load distribution conditions that large-format refill containers must withstand.<\/p>\n

Ergonomic Handle Integration in ISBM Tooling<\/h3>\n

Large-format hand soap containers above 1L fill weight require handles to enable single-handed dispensing and pouring without wrist fatigue. ISBM tooling can incorporate integrated handle features into the blow mould geometry \u2014 most commonly as a moulded grip recess, pinch-handle or D-loop design \u2014 that is formed during the stretch-blow stage without any secondary assembly operation. This is a genuine process distinction from HDPE extrusion blow moulding, which forms handles through parison pinch-off at the parting line, producing a handle that is integral to the bottle but limited in cross-section geometry. ISBM-moulded handles can be designed as fully enclosed loops with defined grip diameter, smooth rounded grip surfaces and label-panel co-planarity that extrusion alternatives cannot achieve. The key design constraint is that the blow stretch ratio into the handle cavity must be compatible with PET’s orientation behaviour \u2014 handle geometries requiring stretch ratios below 1.5:1 typically produce poorly oriented, potentially weak handle zones and require preform or process design input from an experienced plastic bottle manufacturing<\/a> engineer.<\/p>\n

<\/p>\n

\"ISBM<\/div>\n

<\/p>\n

PET vs HDPE for Large-Format Hand Soap Containers<\/h2>\n

The material selection question for large-format hand soap containers is more nuanced than for small retail dispensers, where PET’s clarity advantage is decisive. In the 1L\u20135L format range, HDPE extrusion blow moulding retains a meaningful share of the market \u2014 primarily in institutional bulk formats where appearance matters less and drop impact resistance on warehouse floors is paramount. However, PET’s performance profile increasingly favours ISBM in the retail and semi-professional channels that are driving large-format growth. PET’s biaxially oriented structure provides 40\u201360% higher tensile strength per unit wall thickness than HDPE at equivalent bottle weight \u2014 enabling a 2L PET ISBM bottle at 40g to match the mechanical performance of a 55g HDPE extrusion bottle, delivering a 27% resin saving per unit that compounds to significant cost advantage across high-volume programmes.<\/p>\n

Surface clarity is the most visible performance difference. A 2L PET ISBM hand soap refill bottle with standard bottle-grade resin achieves haze values below 3% \u2014 presenting an essentially clear container through which product colour, fill level and any suspended particles are visible. This transparency is commercially valuable in retail environments where consumers make refill purchasing decisions based on visual product assessment, and in premium personal care channels where packaging appearance equity is part of the brand value proposition. A 2L HDPE extrusion bottle is opaque and cannot participate in these visual merchandising strategies.<\/p>\n

Chemical compatibility considerations for large-format hand soap containers are broadly similar to small retail formats, but storage duration and temperature cycling during distribution deserve additional attention. Large-format containers are typically stored for longer periods between filling and consumer use \u2014 including warehouse pallet storage at temperatures up to 40\u00b0C in Australian summer conditions \u2014 which increases the cumulative thermal exposure of the container-product interface. PET’s low moisture vapour transmission rate protects water-based hand soap formulations from concentration changes during extended storage more effectively than HDPE at equivalent wall gauges. This thermal storage stability advantage of PET is an additional factor supporting ISBM for retail large-format refill programmes where product shelf life declarations of 24\u201336 months are expected.<\/p>\n

<\/div>\n

<\/p>\n

Design Engineering for 1L\u20135L Hand Soap Containers<\/h2>\n

Integrated Handle Design and Grip Ergonomics<\/h3>\n

Handle geometry for large-format hand soap bottles must balance structural integrity, user comfort and ISBM process feasibility. A fully enclosed handle loop with an internal grip diameter of 35\u201345mm accommodates the majority of adult hand sizes comfortably for single-handed pouring; below 30mm internal diameter, arthritic or larger-handed users report grip discomfort that generates consumer complaints and returns. The handle wall gauge after stretch-blow should be maintained at 0.8\u20131.2mm minimum to provide adequate tensile strength against the combined weight of a fully filled 2L container (approximately 2.1kg) under dynamic drop-test conditions. Handle-to-bottle shoulder junction radius must be \u22658mm to distribute stress under load and prevent crack initiation at the re-entrant corner \u2014 a dimension that requires explicit specification in the ISBM blow mould drawing rather than assumption by the mould maker.<\/p>\n

Pouring Neck Design and Dispensing Cap Compatibility<\/h3>\n

Large-format hand soap refill containers use a broader range of dispensing closure formats than small retail bottles. The primary formats are: screw-cap with integral measuring cup for consumer pour-and-measure; flip-top snap-cap for professional dispensing environments; pump overcap for direct-use 1L\u20131.5L table-service formats; and wide-mouth 63mm\u201370mm closures for institutional direct-pour into washroom dispenser reservoirs. Each format requires a specific neck finish standard, and the ISBM preform tooling must be specified to the primary dispensing system selected at the packaging design stage. Neck finish transition across a product range \u2014 for example, a 1L pump format and a 2L pour refill format sharing the same base bottle \u2014 requires either a common neck design or separate preform tooling, a tooling investment trade-off that should be resolved during programme architecture planning before mould design commences.<\/p>\n

<\/p>\n

ISBM Production Workflow for Large-Format Hand Soap Bottles<\/h2>\n

Large-format ISBM production follows the same fundamental four-stage cycle as small-format bottle manufacturing, but with specific adjustments to accommodate higher preform shot weights, longer cooling requirements and the greater cavity footprint of large-format blow moulds.<\/p>\n

\n
\n
\ud83c\udf21\ufe0f<\/div>\n

\u2460 Extended Resin Drying<\/h4>\n

Large-format preforms require more total drying throughput than small-format production at equivalent output rates. Hopper dryer capacity should be sized for 6\u20138 hours residence time at the target throughput rate, maintaining PET below 50 ppm moisture. For rPET blend recipes targeted at large-format sustainability commitments, confirm blend moisture across the combined recipe rather than virgin PET alone, as rPET absorbs atmospheric moisture more rapidly during handling due to its higher surface area.<\/p>\n<\/div>\n

\n
\ud83d\udc89<\/div>\n

\u2461 High-Shot-Weight Preform Injection<\/h4>\n

Large-format preforms for 1L\u20135L containers require shot weights of 25\u201380g depending on bottle size and target wall gauge. Injection fill and hold times are proportionally longer than small-format production, and back-pressure management during screw recovery becomes more critical to avoid IV degradation in the longer plastication dwell. Cavity count per station is typically 1\u20132 for these formats rather than the 4\u20138 common in small-format production.<\/p>\n<\/div>\n

\n
\ud83d\udd25<\/div>\n

\u2462 Multi-Zone Thermal Conditioning<\/h4>\n

Large-format preforms require more conditioning zones and longer conditioning dwell to achieve a uniform temperature gradient through the greater wall thickness and body length. Handle zone conditioning is particularly important: the preform material destined for the integrated handle loop must be conditioned to a temperature range that enables controlled blow into the handle cavity without material starvation at the handle wall or stress whitening from overstretching.<\/p>\n<\/div>\n

\n
\ud83d\udca8<\/div>\n

\u2463 High-Pressure Stretch-Blow<\/h4>\n

Stretch rod travel is proportionally longer for large-format bottles \u2014 a 2L hand soap bottle may require 200\u2013260mm axial rod extension compared to 80\u2013120mm for a 500ml format. Pre-blow pressure timing is critical to avoid premature material rush before adequate axial orientation; high-pressure blow at 30\u201340 bar with extended dwell of 4\u20137 seconds completes full mould contact and ensures handle geometry and base panel dimensions are held consistently across the production run.<\/p>\n<\/div>\n

\n
\ud83d\udce6<\/div>\n

\u2464 Ejection and Downstream Testing<\/h4>\n

Large-format bottles are ejected and transferred to orientation and inline inspection systems configured for their greater footprint and weight. Handle load testing \u2014 applying a 5\u00d7 filled weight tensile force to the handle loop for 60 seconds \u2014 is performed at programme startup and at defined production intervals to validate handle structural integrity before accumulation of filled product inventory at risk from handle failure during palletisation or retail handling.<\/p>\n<\/div>\n<\/div>\n

<\/p>\n

\"Large<\/div>\n

<\/p>\n

ISBM Machine Parameters for Large-Format Hand Soap Container Production<\/h2>\n
\n\n\n\n\n\n\n\n\n\n\n
Parametro<\/th>\nLarge-Format Range (1L\u20135L)<\/th>\nKey Design Consideration<\/th>\n<\/tr>\n<\/thead>\n
Shot weight per cavity<\/td>\n25\u201380g<\/td>\nMachine injection capacity and screw diameter specification<\/td>\n<\/tr>\n
Stretch rod extension<\/td>\n160\u2013280mm<\/td>\nMachine stroke class selection, handle zone orientation<\/td>\n<\/tr>\n
High-pressure blow air<\/td>\n30\u201340 bar<\/td>\nHandle cavity fill completeness, base panel stiffness<\/td>\n<\/tr>\n
tempo di permanenza del soffio<\/td>\n4\u20138 seconds<\/td>\nDimensional accuracy and internal volume consistency<\/td>\n<\/tr>\n
Mould cooling temperature<\/td>\n6\u201312\u00b0C<\/td>\nCrystallinity, handle strength, base stability on pallet<\/td>\n<\/tr>\n
Cycle time (2L bottle)<\/td>\n25\u201340 seconds<\/td>\nOutput rate, cooling adequacy for heavy-walled areas<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

Cycle time for large-format hand soap containers increases non-linearly with bottle volume because cooling requirements scale with wall thickness and total PET mass rather than simply with bottle surface area. A 2L hand soap container with a 40g preform requires cooling dwell times of 5\u20138 seconds \u2014 compared with 2.5\u20134 seconds for a 500ml bottle \u2014 because the greater wall mass retains heat that must be extracted before bottle ejection without causing post-eject dimensional change. Mould cooling circuit design is consequently a more critical engineering variable in large-format tooling: channel pitch, flow rate and inlet temperature uniformity must be specified and validated during mould design review rather than treated as manufacturing details to be resolved in commissioning.<\/p>\n

Cavity count economics also shift significantly in large-format production. Where a 500ml hand soap bottle programme might run 4\u20138 cavities per station, a 2L programme typically runs 1\u20132 cavities per station \u2014 reducing the output rate per machine but increasing the machine’s ability to produce the handle geometry and shoulder profile complexity that larger formats require. Matching machine clamp force to the larger blow mould projected area is a machine selection prerequisite that should be validated against the specific bottle outline and blow pressure during machine specification, not assumed from general-purpose catalogue data.<\/p>\n

<\/p>\n

Quality Assurance for Large-Format Hand Soap Containers<\/h2>\n

Quality testing for large-format hand soap containers encompasses all the standard dimensions applicable to smaller formats \u2014 neck finish gauging, wall thickness measurement, capacity verification, top-load compression, drop testing \u2014 but with specific additions addressing the structural demands of larger filled weights and handle functionality. Handle tensile testing is performed at every production programme startup and at defined in-run sample intervals: a tensile load of five times the filled bottle weight (typically 10\u201312 kg for a 2L container) is applied to the handle loop through a calibrated gauge for 60 seconds, and bottles exhibiting handle deformation, stress whitening or fracture are rejected. Statistical data from handle tensile testing is maintained to identify processing or material trends before handle performance falls below specification.<\/p>\n

Top-load compression performance is particularly important for large-format retail formats that are stacked during palletisation and retail storage. A 2L hand soap bottle in a retail four-high pallet configuration supports approximately 6\u20138 kg of product weight above it \u2014 a cumulative load that, combined with distribution vibration and temperature cycling, can cause creep deformation in bottles with inadequate PET crystallinity or insufficient body wall gauge. Top-load testing at 40\u00b0C for 24 hours under a representative stack load, combined with post-test height and volume measurement, validates the bottle’s creep resistance before commercial production. ISBM-produced PET containers with adequate biaxial orientation consistently pass this protocol at bottle weights that extrusion blow-moulded HDPE alternatives cannot match without significant wall gauge \u2014 and material cost \u2014 increases.<\/p>\n

<\/p>\n

\"Quality<\/div>\n

<\/p>\n

Environmental and Commercial Case for Refill Container Manufacturing<\/h2>\n

The environmental credentials of large-format hand soap refill packaging are well-supported by lifecycle assessment data. A 2L PET ISBM refill container replacing 8\u00d7 250ml single-use retail dispensers reduces total packaging PET by 45\u201355%, cuts secondary corrugated board use by 60\u201370%, and reduces transport fuel consumption per litre of product delivered by 25\u201335% through improved fill density. These reductions translate directly into lower carbon intensity per dispensing event \u2014 a metric increasingly required in corporate procurement specifications for institutional hand soap contracts in healthcare, government and education sectors where sustainability reporting is mandatory.<\/p>\n

For PET large-format containers, recyclability through Australia’s national kerbside system provides an additional end-of-life benefit that institutional buyers can report in their packaging waste metrics. ISBM-produced PET containers above 750ml are accepted by Australian kerbside programmes and MRF optical sorters in all major metropolitan areas, with recovery rates above 70% in major urban centres. Incorporating 25\u201330% rPET content in large-format hand soap containers is achievable on ISBM equipment using current commercial rPET supply, providing a certified recycled content statement that supports both voluntary brand sustainability commitments and contractual procurement requirements in institutional hand soap tender documents. The combination of reduced total packaging volume, recyclable material and validated recycled content makes large-format PET ISBM hand soap containers a compelling choice for brands targeting Australia’s leading packaging sustainability frameworks.<\/p>\n

<\/p>\n

Discuss Your Large-Format Bottle Project \u2192<\/a><\/div>\n

<\/p>\n

Recommended Machine for Large-Format Hand Soap Container Production<\/h2>\n
\n

\"One-step<\/p>\n

\n
Macchina in evidenza<\/div>\n

HGY650-V4: One-Step Four-Station Injection Stretch Blow Moulding Machine<\/h3>\n

The HGY650-V4 is designed for large-format PET container production in the 500ml\u20136,000ml range \u2014 making it the right platform for 1L\u20135L hand soap refill and bulk dispensing programmes. Its larger injection unit, extended stretch rod travel, higher clamp force and enlarged blow mould cavity clearance are configured specifically for the preform weights and blow geometry dimensions that large-format hand soap bottle programmes require. The machine’s independent four-station design provides the conditioning dwell time that heavy-walled large-format preforms need for uniform temperature gradient achievement \u2014 a critical capability for consistent wall thickness distribution in containers with integrated handle geometry or complex shoulder profiles.<\/p>\n

\n
\n
Volume della bottiglia<\/div>\n
500ml \u2013 6,000ml<\/div>\n<\/div>\n
\n
Configurazione<\/div>\n
Rotativa a 4 stazioni<\/div>\n<\/div>\n
\n
Applicazioni<\/div>\n
Refill \u00b7 Bulk \u00b7 Industrial<\/div>\n<\/div>\n<\/div>\n

Visualizza le specifiche complete della macchina \u2192<\/a><\/p>\n<\/div>\n<\/div>\n

<\/p>\n

\"High-output<\/div>\n

<\/p>\n

Domande frequenti<\/h2>\n
\n
\nCan ISBM machines produce PET hand soap bottles with integrated carry handles above 1L?+<\/span><\/summary>\n
Yes \u2014 integrated handles are achievable in ISBM PET containers up to the 5L format range, depending on the handle geometry and stretch ratio into the handle cavity. ISBM handles are formed during the stretch-blow stage when the preform material is driven into the handle loop geometry in the blow mould. The primary design constraint is maintaining a stretch ratio of at least 1.5:1<\/strong> in the handle wall zone to achieve adequate biaxial orientation and mechanical strength. Handles requiring very low stretch ratios \u2014 as in wide, flat grip designs \u2014 may require supplemental conditioning temperature management to maintain adequate material formability. Australia Ever-Power ISBM machines in the HGY650-V4 class are configured with the stretch rod travel length, clamp force and conditioning zone control needed for integrated handle production in the 1L\u20135L format range. Contact sales@isbm-technology.com<\/a> with your handle geometry specification for process feasibility review.<\/div>\n<\/details>\n
\nHow does ISBM compare to HDPE extrusion blow moulding for 2L hand soap bottles?+<\/span><\/summary>\n
The key performance differences for 2L hand soap containers are: Clarity<\/strong> \u2014 ISBM PET is essentially clear (haze <3%); HDPE extrusion is opaque. Wall efficiency<\/strong> \u2014 biaxially oriented PET achieves equivalent strength at 25\u201335% lower wall gauge and bottle weight compared to HDPE. Neck precision<\/strong> \u2014 ISBM injection-formed necks hold \u00b10.10mm tolerances; HDPE extrusion necks hold \u00b10.20\u20130.30mm. Surface finish<\/strong> \u2014 ISBM PET achieves Ra 0.05\u20130.15\u00b5m surface; HDPE extrusion achieves Ra 0.4\u20131.0\u00b5m, limiting label adhesion and print quality. Drop impact<\/strong> \u2014 HDPE retains a marginal advantage at very low temperatures (-20\u00b0C and below) in institutional environments. For retail, food service and healthcare applications where presentation quality and packaging sustainability metrics are primary drivers, ISBM PET large-format containers offer a compelling combined performance advantage over HDPE extrusion alternatives.<\/div>\n<\/details>\n
\nWhat is the typical cycle time and output rate for a 2L hand soap refill bottle?+<\/span><\/summary>\n
A 2L PET hand soap container with an integrated handle and a target bottle weight of 40\u201350g typically requires a cycle time of 28\u201338 seconds<\/strong> on a four-station ISBM machine, depending on preform wall thickness, mould cooling circuit efficiency and handle complexity. Running a 2-cavity tool configuration \u2014 standard for this format \u2014 produces 180\u2013250 bottles per hour per cavity set<\/strong>, yielding 360\u2013500 bottles per hour total output. For comparison, a 4-cavity 500ml tool on the same machine platform produces 900\u20131,400 bottles per hour. Large-format production economics are therefore evaluated on a per-litre-of-capacity basis rather than bottles-per-hour: a 2L production run delivers equivalent litre output to a 500ml run at approximately 50% of the bottle count, with proportionally higher material throughput per machine hour that maintains equipment utilisation efficiency across the format mix.<\/div>\n<\/details>\n
\nHow much rPET content can be incorporated into large-format hand soap refill containers?+<\/span><\/summary>\n
Large-format PET ISBM containers can typically incorporate 25\u201350% bottle-grade rPET<\/strong> depending on the rPET stream quality and the bottle’s visual and mechanical acceptance criteria. At 25\u201330% rPET, clear large-format hand soap containers remain visually competitive with virgin-PET equivalents in retail environments. At 30\u201350% content, slight haze increase becomes perceptible for clear designs but is often acceptable for coloured, frosted or semi-opaque bottle variants. Processing adjustments for high rPET blends include slightly elevated injection temperature (+3\u20135\u00b0C), extended conditioning dwell, and confirmation that blend IV remains above 0.74 dL\/g. Australia Ever-Power technical teams can support rPET blend recipe development for large-format hand soap programmes and advise on material specification based on the rPET stream sources and quality available through your supply chain.<\/div>\n<\/details>\n
\nAre large-format PET hand soap containers accepted in Australia’s kerbside recycling system?+<\/span><\/summary>\n
Yes \u2014 mono-material PET containers from 200ml upward are accepted by the Australian kerbside recycling system and are identified and sorted by the NIR optical sorters at Material Recovery Facilities (MRFs) into the PET (01) stream. Large-format PET containers above 1L are processed through the same MRF optical sorting infrastructure as smaller bottles, provided they carry the PET resin identification code and contain no metal or non-PET label face that would complicate sortation. Removing pump closures and rinsing the container before bin placement is recommended by ARL guidelines to maximise recovered rPET quality. For containers incorporating rPET and labelled under the Australasian Recycling Label (ARL)<\/strong> framework, the ‘Recycle’ designation is substantiated by the mono-material PET construction and kerbside acceptance confirmation \u2014 a reporting-ready claim for APCO annual reporting and institutional procurement sustainability documentation.<\/div>\n<\/details>\n<\/div>\n

<\/p>\n

\n
\n
Australia Ever-Power<\/div>\n
Injection Stretch Blow Moulding Machine Co., Ltd<\/div>\n
Condell Park NSW 2200, Sydney, Australia<\/div>\n<\/div>\n
sales@isbm-technology.com<\/a>
\nContattaci \u2192<\/a><\/div>\n<\/div>\n<\/div>","protected":false},"excerpt":{"rendered":"

Application Insight \u00b7 Hand Care Packaging As refill and bulk-buy formats reshape the hand soap category, 1L\u20135L bottles are becoming a production priority. This guide covers how stretch blow molding technology handles large-format hand soap container manufacturing \u2014 from handle integration to high-output ISBM machine selection. ISBM Technology Refill Bottle Manufacturing Large-Format PET Containers Large-format […]<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"categories":[24],"tags":[],"class_list":["post-498","post","type-post","status-publish","format-standard","hentry","category-application"],"_links":{"self":[{"href":"https:\/\/isbm-technology.com\/it\/wp-json\/wp\/v2\/posts\/498","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/isbm-technology.com\/it\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/isbm-technology.com\/it\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/isbm-technology.com\/it\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/isbm-technology.com\/it\/wp-json\/wp\/v2\/comments?post=498"}],"version-history":[{"count":3,"href":"https:\/\/isbm-technology.com\/it\/wp-json\/wp\/v2\/posts\/498\/revisions"}],"predecessor-version":[{"id":504,"href":"https:\/\/isbm-technology.com\/it\/wp-json\/wp\/v2\/posts\/498\/revisions\/504"}],"wp:attachment":[{"href":"https:\/\/isbm-technology.com\/it\/wp-json\/wp\/v2\/media?parent=498"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/isbm-technology.com\/it\/wp-json\/wp\/v2\/categories?post=498"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/isbm-technology.com\/it\/wp-json\/wp\/v2\/tags?post=498"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}